[分享][原創] 16*48點陣制作（附原理圖和代碼）

ID:3795 · 發表于 2010-1-4 17:54

突然之間，心血來潮，想做個點陣玩玩。于是，便干起來了。

上星期六，如期來到了崗頂，賽格電子城，走上二樓，去到我經常買零件的檔位。由于經常去她那里買零件，更老板娘也挺熟的了，沒喧寒幾句，我就把我要買的零件的清單遞給了她。買零件買了很久，一來要買的東西太多了，二來也很多人買東西。到結算時，要100來塊，哇。。。心疼啊。我買了12個8*8的點陣，一個5塊，那也去了60塊了，還有加上其他零件，零零碎碎的，真的是小數怕長計啊。

在買零件之前，其實我已經畫好了原理圖的了,上個星期和這個星期的前兩天，我一直在焊接電路，焊得我頭暈目眩的，飛線飛到我癡線啊。看看下面的照片就知道我的辛酸了。

主控板的背面走線

這張照片太有紀念意義了，我記得那天，星期二，我一天都沒課，我從早上8點多一直在焊，一直焊到晚上11點多，期間除了吃中午飯外，那個烙鐵就沒有離開過我的手。終于在晚上11點多把硬件部分搞定了，緊接著，我就想試試我硬件到底有沒有問題，所以，立馬寫了一個測試程序，下載到單片機上讓它運行，我點亮了第一列的8個LED ，正如我所愿。又緊接著，我把程序修改一個，我要掃描整個點陣，我要看看有沒有不亮或接線有問題的。我把程序下載到板子上，出現了如上圖的畫面，實在太令人激動了，接線基本沒問題，只是第15列和第16列接反了，但問題不大，我重新接好之后，板子一切正常。

今天我寫了一個下午的程序，終于把“機電系”給顯示出來了，哈哈！~太興奮了~

然后，當然要有我的LOGO啦，哈哈！~~

YEE制造

1648點陣.rar (210.1 KB, 下載次數: 418)

ID:19368 · 發表于 2010-1-4 18:12

強！

顯示的字符要是能夠直接在電腦上更改，那就有實用價值了！

ID:20827 · 發表于 2010-1-6 18:35

不錯，，，，，，，附上樓主代碼方便沒有黑幣的朋友：

#include<reg52.h>
#define uchar unsigned char
#define uint unsigned int
#define speed 10
sbit h8=P2^7;
sbit l8=P2^6;
sbit clk=P2^5;
sbit rck=P2^4;
sbit ser=P2^3;
uchar code table[]={0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x40,0x00,0x30,0xFC,0x0F,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x05,0x00,
0x06,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x00,0x00,/*"廣",0*/
0x00,0x00,0x04,0x00,0x04,0x20,0xC4,0x18,0xB4,0x0E,0x8C,0x04,0x87,0x20,0x84,0x40,
0xF4,0xFF,0x84,0x00,0x84,0x02,0x84,0x04,0x84,0x18,0x04,0x30,0x00,0x00,0x00,0x00,/*"東",1*/
0xC4,0x08,0xB4,0x08,0x8F,0x08,0xF4,0xFF,0x84,0x04,0x84,0x44,0x04,0x41,0x82,0x41,
0x42,0x41,0x22,0x41,0x12,0x7F,0x2A,0x41,0x46,0x41,0xC2,0x41,0x00,0x41,0x00,0x00,/*"輕",2*/
0x00,0x20,0x00,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0xFE,0x3F,
0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x02,0x20,0x00,0x20,0x00,0x00,/*"工",3*/
0x02,0x10,0x02,0x10,0xFE,0x0F,0x92,0x08,0x92,0x08,0xFE,0xFF,0x02,0x04,0x00,0x44,
0xFE,0x21,0x82,0x1C,0x82,0x08,0x82,0x00,0x82,0x04,0xFE,0x09,0x00,0x30,0x00,0x00,/*"職",4*/
0x00,0x20,0x10,0x20,0x60,0x20,0x80,0x23,0x00,0x21,0xFF,0x3F,0x00,0x20,0x00,0x20,
0x00,0x20,0xFF,0x3F,0x00,0x22,0x80,0x21,0x60,0x20,0x38,0x30,0x10,0x20,0x00,0x00,/*"業",5*/
0x08,0x01,0x08,0x41,0x88,0x80,0xFF,0x7F,0x48,0x00,0x28,0x40,0x00,0x40,0xC8,0x20,
0x48,0x13,0x48,0x0C,0x7F,0x0C,0x48,0x12,0xC8,0x21,0x48,0x60,0x08,0x20,0x00,0x00,/*"技",6*/
0x10,0x10,0x10,0x10,0x10,0x08,0x10,0x04,0x10,0x02,0x90,0x01,0x50,0x00,0xFF,0x7F,
0x50,0x00,0x90,0x00,0x12,0x01,0x14,0x06,0x10,0x0C,0x10,0x18,0x10,0x08,0x00,0x00,/*"術",7*/
0x40,0x00,0x30,0x02,0x10,0x02,0x12,0x02,0x5C,0x02,0x54,0x02,0x50,0x42,0x51,0x82,
0x5E,0x7F,0xD4,0x02,0x50,0x02,0x18,0x02,0x57,0x02,0x32,0x02,0x10,0x02,0x00,0x00,/*"學",8*/
0xFE,0xFF,0x02,0x00,0x32,0x02,0x4A,0x04,0x86,0x83,0x0C,0x41,0x24,0x31,0x24,0x0F,
0x25,0x01,0x26,0x01,0x24,0x7F,0x24,0x81,0x24,0x81,0x0C,0x81,0x04,0xF1,0x00,0x00,/*"院",9*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x18,0x06,0x98,0x03,0xFF,0x7F,0xFF,0x7F,0x98,0x01,0x18,0x23,0x00,0x70,0xFE,0x3F,
0xFE,0x0F,0x06,0x00,0x06,0x00,0xFE,0x3F,0xFE,0x7F,0x00,0x60,0x00,0x70,0x00,0x00,/*"機",0*/
0x00,0x00,0x00,0x00,0xFC,0x0F,0xFC,0x0F,0x4C,0x06,0x4C,0x06,0xFF,0x3F,0xFF,0x7F,
0x4C,0x66,0x4C,0x66,0x4C,0x66,0xFC,0x67,0xFC,0x67,0x00,0x78,0x00,0x38,0x00,0x00,/*"電",1*/
0x00,0x00,0x00,0x20,0x06,0x33,0x26,0x1B,0x36,0x0B,0xBE,0x03,0xEE,0x63,0x66,0x7F,
0x26,0x3F,0x36,0x01,0x1B,0x01,0xCB,0x09,0x83,0x19,0x03,0x33,0x00,0x00,0x00,0x00,/*"系",2*/
0x70,0x30,0x78,0x37,0xEF,0x37,0x77,0x36,0x30,0x36,0x60,0x00,0xF8,0x7F,0xFF,0x7F,
0xDF,0x36,0xD8,0x36,0xFB,0x3F,0xFE,0x3F,0xD8,0x36,0xD8,0x36,0x18,0x30,0x00,0x00,/*"維",3*/
0x60,0x00,0x30,0x00,0xFC,0x7F,0xFF,0x7F,0x03,0x00,0xF0,0x0F,0xD0,0x40,0xDC,0x52,
0x4F,0x6A,0x77,0x2D,0x26,0x35,0x7E,0x16,0x5E,0x1A,0xC6,0x08,0xC0,0x00,0x00,0x00,/*"修",4*/
0xC0,0x00,0xCC,0x7E,0xDC,0x7E,0xEF,0x36,0xCF,0x36,0xEC,0x36,0xDC,0x7E,0xCC,0x7E,
0x00,0x00,0xFE,0x7F,0xFE,0x7F,0x06,0x18,0xE6,0x18,0xFE,0x1F,0x1E,0x0F,0x00,0x00,/*"部",5*/
0x08,0x00,0x38,0x00,0xC8,0x20,0x00,0x3F,0xC8,0x20,0x38,0x00,0x08,0x00,0x00,0x00,/*"Y",0*/
0x08,0x20,0xF8,0x3F,0x88,0x20,0x88,0x20,0xE8,0x23,0x08,0x20,0x10,0x18,0x00,0x00,/*"E",1*/
0x08,0x20,0xF8,0x3F,0x88,0x20,0x88,0x20,0xE8,0x23,0x08,0x20,0x10,0x18,0x00,0x00,/*"E",2*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",3*/
0x00,0x00,0x50,0x00,0x4F,0x3F,0x4A,0x01,0x48,0x01,0xFF,0xFF,0x48,0x21,0x48,0x61,
0x48,0x3F,0x00,0x00,0xFC,0x0F,0x00,0x40,0x00,0x80,0xFF,0x7F,0x00,0x00,0x00,0x00,/*"制",4*/
0x40,0x40,0x41,0x20,0xC6,0x1F,0x00,0x20,0x40,0x40,0x50,0x40,0x4E,0x5F,0x48,0x49,
0x48,0x49,0x7F,0x49,0x48,0x49,0x48,0x49,0x48,0x5F,0x48,0x40,0x40,0x40,0x00,0x00,/*"造",5*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};
/*void delay(uint k)
{
uint i,j;
for(i=0;i<k;i++)
{
for(j=0;j<121;j++){;}
}
}*/
void hc595_move()
{
clk=1;
clk=0;
rck=1;
rck=0;
ser=1;
}
void hc595int()
{
uchar i;
h8=1; l8=1;
P0=0x00;
P2=0x00;
h8=0; l8=0;
for(i=0;i<48;i++)
{
ser=1;
hc595_move();
}
}
void main()
{
uint i,j,m,n,s,c;
hc595int();
ser=0;
hc595_move();
while(1)
{
for(i=0;i<384;i++)
{
for(s=0;s<speed;s++)
{
m=2*i;n=2*i+1;
for(j=1;j<=48;j++)
{
m=m+2;n=n+2;
P0=table[n];
l8=1;
l8=0;
P0=table[m];
h8=1;
h8=0;
for(c=0;c<5;c++);
P0=0x00;
h8=1;l8=1;
h8=0;l8=0;
hc595_move();
}
ser=0;
hc595_move();
}
}
}
}

復制代碼

ID:45233 · 發表于 2012-10-4 23:25

難得啊！

ID:24355 · 發表于 2012-10-9 21:38

難得啊！

ID:43173 · 發表于 2012-10-12 08:37

以下是引用wyx1144在2010-1-4 18:12:59的發言：

強！

顯示的字符要是能夠直接在電腦上更改，那就有實用價值了！

再加個通信接口，又要不少鈔票啊！

ID:15906 · 發表于 2012-10-13 19:48

這個貌似還可以

ID:55203 · 發表于 2013-9-19 14:50

ID:55217 · 發表于 2013-10-8 23:10

不錯！

ID:52286 · 發表于 2013-10-13 23:41

支持支持！！

ID:51142 · 發表于 2014-4-5 22:50

下載學習學習，

ID:61326 · 發表于 2014-5-2 19:46

謝謝分享！

ID:59572 · 發表于 2014-5-2 20:21

下面的圖片看不到
不過謝謝分享

ID:61200 · 發表于 2014-5-2 22:05

樓主在崗頂買零件啊，我也經常去哪里。

ID:32572 · 發表于 2014-5-3 00:12

圖片掛了

ID:23303 · 發表于 2014-5-11 08:32

顯示的字符要是能夠直接在電腦上更改，那就有實用價值了

ID:65962 · 發表于 2014-9-9 16:41

謝謝分享

ID:47760 · 發表于 2014-9-13 05:05

感謝樓主分享

ID:47760 · 發表于 2014-9-13 05:06

感謝樓主分享

ID:66181 · 發表于 2014-9-15 10:37

謝謝分享

ID:66338 · 發表于 2014-9-18 16:43

強！

顯示的字符要是能夠直接在電腦上更改，那就有實用價值了！

ID:68021 · 發表于 2014-10-28 15:18

不錯不錯不錯

ID:68112 · 發表于 2014-10-30 10:57

而對OK怕、

ID:66060 · 發表于 2014-11-15 13:07

下載后，為什么仿真軟件不能運行

ID:69063 · 發表于 2014-11-19 20:59

支持一個

ID:69063 · 發表于 2014-11-19 21:00

支持一個

ID:69063 · 發表于 2014-11-19 21:00

支持一個

ID:64053 · 發表于 2014-11-26 14:30

又是曬東西,給點資料也好呀,

ID:67132 · 發表于 2014-11-26 16:29

不錯不過點陣1個5塊錢貴了點雖然是2010年

ID:47760 · 發表于 2014-11-28 03:24

不錯，學習學習

ID:47760 · 發表于 2014-11-29 04:53

謝謝分享！

ID:84077 · 發表于 2015-6-27 15:46

強大牛

ID:53925 · 發表于 2015-7-3 08:59

如果能與電腦通訊就更加完美了----

ID:90737 · 發表于 2015-9-26 10:27

為什么我的運行出錯了

ID:97705 · 發表于 2015-11-30 15:29

不錯，不錯，不錯

ID:143871 · 發表于 2016-12-18 17:54

很好，點贊

ID:261637 · 發表于 2017-12-15 17:27

咋仿真不顯示

ID:261637 · 發表于 2017-12-16 14:46

咋仿真不顯示.求解？

帳號		自動登錄	找回密碼
密碼			立即注冊

wwwxxx国产_337p日本欧洲亚洲大胆张筱雨_免费在线看成人av_日本黄色不卡视频_国产精品成熟老女人_99视频一区_亚洲精品97久久中文字幕_免费精品视频在线_亚洲色图欧美视频_欧美一区二三区

[分享][原創] 16*48點陣制作（附原理圖和代碼）

評分