開源自己做的CPLD+SRAM液晶驅動verilog代碼

ID:558132 · 發表于 2019-6-9 15:59

斷斷續續地學了verilog HDL和FPGA一段時間，一直沒有完整的做一個東西，看到論壇上有做TFT控制器的，于是就仿制了一個.
verilog程序大部分是自己寫的，一些部分如異步寫入，HSync,VSync時序產生部分參考了"dzng11"
廢話不說了：直接上圖上資料

電路原理圖如下：

verilog HDL源程序如下:

/**********************************************************************
通用4.3寸tft驅動
地址1位
-----------------------------------------------------------------——----
A0=0寄存器，寄存器0-7
0 SRAM數據
1 xIdex x軸寄存器
2 yIdex y軸寄存器
3 yend 結束寄存器，用于窗口繪圖加速
4 前景顏色
5 背景色
6
7 系統狀態0-15位
bo-b2 b3 b4-b6 b7-b9 b10-b12
背光顯示開/關顯示方式要寫入的頁當前顯示頁
必須位x00 必須位x00
x可改變（b7） x可改變（b10）
-----------------------------------------------------------------------
AO=1數據
2011.12.5
***********************************************************************/
/*
接口說明:
Clk54:系統晶振,選擇54M晶振
SysRst:系統復位線.
ExDataBus:外部16位數據總線
ExCs:控制器片選,
ExRs:數據批令選擇
ExWr:寫信號
ExRd:讀信號
RamAddrBus:顯存地址線.
RamDataBus:顯存數據總線
RamCs:顯存片選
RamWe:顯存寫選通.
LedOn:背光控制PWM
DE:TFT屏
DE:VSyncTFT屏,
HSync:TFT屏
RGB:TFT屏
Pclk:TFT屏);
*/
module tft43(Clk54, SysRst, ExDataBus, ExCs, ExRs, ExWr, ExRd, RamAddrBus,
RamDataBus, RamCs, RamWe,RamOe, LedOn, DE, VSync, HSync, RGB, Pclk);
input Clk54, SysRst, ExCs, ExRs, ExRd, ExWr;
inout [15:0] ExDataBus;
inout [15:0] RamDataBus;
output [17 : 0] RamAddrBus;
output [15:0] RGB;
output RamCs, RamWe,RamOe, LedOn, DE, VSync, HSync, Pclk;
reg [2:0] ClkCnt_Q3;
reg DotClkEn_Q;
reg Pclk_Q;
reg WrEn_Q;
reg [15:0]ExBusOut_Q;
reg [15:0] ExOutM;
reg [15:0] WriteRgb_Q;
reg ExWrClk_Q;
reg ExRsR_Q;
reg ExCsR_Q;
reg ExRdClk_Q;
reg ExRdClk_Q1;
reg ExRdClk_Q2;
reg ExWrClk_Q1;
reg ExWrClk_Q2;
reg [12:0] SramAddr;
reg [15:0] PrePareData;
reg [7:0] IndexData;
reg InRamWe;
reg IncAddr;
reg XRegOver;
reg YRegOver;
reg AskWr;
reg [15:0] RGB_Q;
reg [15:0] InBusOut_Q;
reg [8:0] XRegValue_Q;
reg [8:0] YRegValue_Q;
reg [15:0] SysCmdValue_Q;
reg [2:0] RegAddr_Q;
reg RamWeReg_Q;
reg RamTriState_Q;
reg [2:0] FillCount_Q;
reg [15:0] BRGBValue_Q;
reg [15:0] FRGBValue_Q;
reg [17:0] RamAddrBus_Q;
reg FillHead_Q;
reg [8:0] HsCount_Q;
reg [8:0] DotCount_Q;
reg SelDispRam_Q;
reg RamCsReg_Q;
reg DsMark;
reg HsMark;
reg [1:0]DsState_Q;
reg [1:0]HsState_Q;
reg DE_Q;
reg [4:0]LedCount_Q;
reg LedOn_Q,LedOn_W;
assign Pclk = Pclk_Q;
assign RGB = RGB_Q;
assign RamAddrBus = {RamAddrBus_Q};
assign RamWe = RamWeReg_Q;
assign RamCs = RamCsReg_Q;
assign RamOe = RamCsReg_Q;/////
assign RamDataBus = (RamTriState_Q | Clk54)?16'bzzzzzzzzzzzzzzzz:InBusOut_Q;
assign VSync = DE_Q;
assign HSync = DE_Q;//1'b0;
assign DE = DE_Q;
assign LedOn = LedOn_Q;
assign ExDataBus = ExOutM;
/*
--1.將54M主時鐘6分頻,產生9M時鐘并輸出至引腳Pclk
--2.輸出DotClkEn為9M信號同步其他進程.高電平為1個主時鐘周期,低電平5個主時鐘周期
--3.技巧: 001,010,011,100,101,110.共6個狀態,高位剛好是6分頻等寬.
*/
always @(posedge Clk54 or negedge SysRst)
begin
if (!SysRst) begin
ClkCnt_Q3 = 3'd1;
Pclk_Q = 1'b0;
DotClkEn_Q = 1'b0;
end else begin
if (ClkCnt_Q3[2] & ClkCnt_Q3[1]) begin
ClkCnt_Q3 <= 3'd1;
end else begin
ClkCnt_Q3 <= ClkCnt_Q3 + 3'd1;
end
Pclk_Q <= (SysCmdValue_Q[3])?1'b0:ClkCnt_Q3[2];
DotClkEn_Q <= ((~ClkCnt_Q3[2]) & ClkCnt_Q3[1] & ClkCnt_Q3[0]);
end
end
/*
--外部接口在RD及CS低電平期間輸出內部數據
--RS為0時輸出忙信號.RS為1時輸出當前地址的內部數據
*/
always @(SysRst or ExBusOut_Q or WrEn_Q or ExCs or ExRs or ExWr or ExRd)
begin
if (!SysRst) begin
ExOutM = 16'bzzzzzzzzzzzzzzzz;
end else begin
if ((~ExCs) & ExWr & (~ExRd)) begin
ExOutM = (ExRs)?ExBusOut_Q:({15'd0,WrEn_Q});
end else begin
ExOutM = 16'bzzzzzzzzzzzzzzzz;
end
end
end
/*
--外部異步WR寫入數據.
*/
always @(posedge ExWr or negedge SysRst)
begin
if (!SysRst) begin
WriteRgb_Q = 16'd0;
ExWrClk_Q = 1'b0;
RegAddr_Q = 3'd0;
end else begin
if (!ExCs) begin
if (!ExRs) begin
RegAddr_Q <= ExDataBus[2:0];
end else begin
WriteRgb_Q <= ExDataBus;
ExWrClk_Q <= ~ExWrClk_Q;
end
end
end
end
/*
--外部異步RD讀出數據.
*/
always @(negedge ExRd or negedge SysRst)
begin
if (!SysRst) begin
ExRsR_Q = 1'b0;
ExCsR_Q = 1'b1;
end else begin
ExCsR_Q <= ExCs;
ExRsR_Q <= ExRs;
end
end
always @(posedge ExRd or negedge SysRst)
begin
if (!SysRst) begin
ExRdClk_Q = 1'b0;
end else begin
if ((~ExCsR_Q) & ExRsR_Q) begin
ExRdClk_Q <= ~ExRdClk_Q;
end
end
end
/******************************************
--主時鐘打兩拍同步采用外部讀寫信號
******************************************/
always @(posedge Clk54 or negedge SysRst)
begin
if (!SysRst) begin
ExRdClk_Q1 = 1'b0;
ExRdClk_Q2 = 1'b0;
ExWrClk_Q1 = 1'b0;
ExWrClk_Q2 = 1'b0;
end else begin
ExRdClk_Q1 <= ExRdClk_Q;
ExRdClk_Q2 <= ExRdClk_Q1;
ExWrClk_Q1 <= ExWrClk_Q;
ExWrClk_Q2 <= ExWrClk_Q1;
end
end
always @(posedge Clk54 or negedge SysRst)
begin
if (!SysRst) begin
InBusOut_Q = 16'd0;
ExBusOut_Q = 16'd0;
XRegValue_Q = 9'd0;
YRegValue_Q = 9'd0;
SysCmdValue_Q = 16'b0000000000110000;
WrEn_Q = 1'b0;
RamWeReg_Q = 1'b1;
RamTriState_Q = 1'b1;
RGB_Q = 16'd0;
FillCount_Q = 3'd7;
BRGBValue_Q = 16'd0;
FRGBValue_Q = 16'd0;
RamAddrBus_Q = 18'd0;
RamCsReg_Q = 1'b1;
PrePareData = 16'd0;
end else begin
if (ExRdClk_Q2 ^ ExRdClk_Q1) begin
IncAddr = 1'b1;
end else begin
IncAddr = 1'b0;
end
if (ExWrClk_Q2 ^ ExWrClk_Q1) begin
AskWr = 1'b1;
end else begin
AskWr = WrEn_Q;
end
XRegOver = (XRegValue_Q == 9'b111011111)?1'b1:1'b0;
YRegOver = (YRegValue_Q == 9'b100001111)?1'b1:1'b0;
PrePareData = WriteRgb_Q;
IndexData[7:0] = WriteRgb_Q[7:0];
InRamWe = 1'b1;
if (!ClkCnt_Q3[0]) begin
if (AskWr) begin
case (RegAddr_Q)
3'b000:begin
XRegValue_Q <= PrePareData[8:0];
WrEn_Q <= 1'b0;
end
3'b001:begin
YRegValue_Q <= PrePareData[8:0];
WrEn_Q <= 1'b0;
end
3'b010:begin
InRamWe = 1'b0;
IncAddr = 1'b1;
WrEn_Q <= 1'b0;
end
3'b100:begin
FRGBValue_Q <= PrePareData;
WrEn_Q <= 1'b0;
end
3'b101:begin
BRGBValue_Q <= PrePareData;
WrEn_Q <= 1'b0;
end
3'b110:begin
SysCmdValue_Q <= PrePareData;
WrEn_Q <= 1'b0;
end
3'b011:begin
if (!IndexData[FillCount_Q]) begin
PrePareData = BRGBValue_Q;
InRamWe = SysCmdValue_Q[12];
end else begin
PrePareData = FRGBValue_Q;
InRamWe = 1'b0;
end
IncAddr = 1'b1;
WrEn_Q <= (FillCount_Q[0] | FillCount_Q[1] | FillCount_Q[2]);
FillCount_Q <= FillCount_Q + 3'd7;
end
3'b111:begin
if (FillHead_Q) begin
IncAddr = 1'b1;
InRamWe = 1'b0;
if (YRegOver & XRegOver) begin
WrEn_Q <= 1'b0;
end
end else begin
WrEn_Q <= 1'b1;
end
end
endcase
end
RGB_Q <= (SysCmdValue_Q[3])?16'd0:RamDataBus;
SramAddr[12:4] = YRegValue_Q[8:0];
SramAddr[3:0] = XRegValue_Q[8:5];
RamAddrBus_Q[4:0] <= XRegValue_Q[4:0];
RamAddrBus_Q[17] <= SysCmdValue_Q[7];
end else begin
if (AskWr) begin
WrEn_Q <= 1'b1;
end
ExBusOut_Q <= RamDataBus;
SramAddr[12:4] = HsCount_Q[8:0];
SramAddr[3:0] = DotCount_Q[8:5];
RamAddrBus_Q[4:0] <= DotCount_Q[4:0];
RamAddrBus_Q[17] <= SelDispRam_Q;
end
InBusOut_Q <= PrePareData;
RamTriState_Q <= InRamWe;
RamWeReg_Q <= InRamWe;
SramAddr[12:0] = SramAddr[12:0] - {4'd0,SramAddr[12:4]};
RamAddrBus_Q[16:5] <= SramAddr[11:0];
/*根據配置字調整XY*/
if (IncAddr) begin
case (SysCmdValue_Q[6:4])
3'b001:begin
if (XRegOver) begin
XRegValue_Q <= 9'd0;
end else begin
XRegValue_Q <= XRegValue_Q + 9'd1;
end
end
3'b011:begin
if (XRegOver) begin
XRegValue_Q <= 9'd0;
if (YRegOver) begin
YRegValue_Q <= 9'd0;
end else begin
YRegValue_Q <= YRegValue_Q + 9'd1;
end
end else begin
XRegValue_Q <= XRegValue_Q + 9'd1;
end
end
3'b110:begin
if (YRegOver) begin
YRegValue_Q <= 9'd0;
end else begin
YRegValue_Q <= YRegValue_Q + 9'd1;
end
end
3'b111:begin
if (YRegOver) begin
YRegValue_Q <= 9'd0;
if (XRegOver) begin
XRegValue_Q <= 9'd0;
end else begin
XRegValue_Q <= XRegValue_Q + 9'd1;
end
end else begin
YRegValue_Q <= YRegValue_Q + 9'd1;
end
end
default:begin
end
endcase
end
RamCsReg_Q <= SysCmdValue_Q[3];
end
end
/*--產生TFT行同步*/
always @(posedge Clk54 or negedge SysRst)
begin
if (!SysRst) begin
DotCount_Q = 9'd0;
DsState_Q = 2'd0;
DsMark = 1'b0;
end else begin
if (DotClkEn_Q) begin
case (DsState_Q)
2'd0:/*=>--41 相當于<= 40*/
DsMark = (DotCount_Q[5] & DotCount_Q[3]);
2'd1:/*when "01" =>--2 相當于<= 1*/
DsMark = DotCount_Q[0];
2'd2:/*=>--480 相當于<= 479*/
DsMark = (DotCount_Q[0] & DotCount_Q[1] & DotCount_Q[2] & DotCount_Q[3] &
DotCount_Q[4] & DotCount_Q[6] & DotCount_Q[7] & DotCount_Q[8]);
2'd3:/*--2 相當于<= 1*/
DsMark = DotCount_Q[0];
endcase
DsState_Q <= DsState_Q + {1'b0,DsMark};
DotCount_Q <= (DsMark)?9'd0:(DotCount_Q + 9'd1);
end
end
end
/*--產生TFT幀同步信號*/
always @(posedge Clk54 or negedge SysRst)
begin
if (!SysRst) begin
DE_Q = 1'b0;
end else begin
DE_Q <= (SysCmdValue_Q[3])?1'b0:(HsState_Q[1] & (~HsState_Q[0]) & DsState_Q[1] & (~DsState_Q[0]));
end
end
/*--產生幀同步時鐘*/
always @(posedge Clk54 or negedge SysRst)
begin
if (!SysRst) begin
HsCount_Q = 9'd0;
HsState_Q = 2'd0;
FillHead_Q = 1'b0;
SelDispRam_Q = 1'b0;
LedCount_Q = 5'd0;
end else begin
……………………
…………限于本文篇幅余下代碼請從51黑下載附件…………

復制代碼

所有資料51hei提供下載:

tft43.rar (9.52 MB, 下載次數: 112)

stm32程序.7z (559.44 KB, 下載次數: 87)

ID:199411 · 發表于 2019-9-6 11:47

謝謝分享

ID:199411 · 發表于 2019-9-6 13:51

正好需要，放謝分享

ID:265614 · 發表于 2019-10-10 15:05

SramAddr[12:4] = YRegValue_Q[8:0];
            SramAddr[3:0] = XRegValue_Q[8:5];
            RamAddrBus_Q[4:0] <= XRegValue_Q[4:0];
            RamAddrBus_Q[17] <= SysCmdValue_Q[7];
版主能解釋一下這段代碼嗎

ID:265614 · 發表于 2019-10-23 14:42

這個板子哪里有賣

ID:97678 · 發表于 2019-12-8 14:08

這個板子有的賣嗎？想買一個看看，找了很久才發現

ID:483587 · 發表于 2020-1-2 17:01

這個板子有的賣嗎？想買一個看看，找了很久才發現

ID:726712 · 發表于 2020-4-11 08:24

寫的不錯，謝謝樓主開源

ID:242064 · 發表于 2020-5-28 11:50

我也想買一個？板子有買的嗎？

ID:242064 · 發表于 2020-5-29 23:31

ExOutM = (ExRs)?ExBusOut_Q:({15'd0,WrEn_Q}

ID:242064 · 發表于 2020-5-29 23:33

是什么意思？

ID:242064 · 發表于 2020-5-29 23:43

ExOutM = (ExRs)?ExBusOut_Q:({15'd0,WrEn_Q});

ID:242064 · 發表于 2020-6-11 23:42

是拼接

ID:77220 · 發表于 2020-8-17 05:10

thanks very good

ID:83553 · 發表于 2020-9-4 08:27

板子有買的嗎？

ID:575109 · 發表于 2020-10-5 21:58

剛學一個月，感覺這代碼問題挺多，時序邏輯語句塊中間使用了阻塞賦值，這樣不對吧？！另外這些塊內部描述的語句過多，估計很難綜合出正確的結果

ID:434018 · 發表于 2022-7-17 10:19

看看!
寫的不錯!

ID:97678 · 發表于 2022-9-14 12:13

好東西！值得收藏

ID:97678 · 發表于 2022-9-14 12:16

樓主，能夠分享一下原理圖和PCB嗎？

帳號		自動登錄	找回密碼
密碼			立即注冊

wwwxxx国产_337p日本欧洲亚洲大胆张筱雨_免费在线看成人av_日本黄色不卡视频_国产精品成熟老女人_99视频一区_亚洲精品97久久中文字幕_免费精品视频在线_亚洲色图欧美视频_欧美一区二三区

開源自己做的CPLD+SRAM液晶驅動verilog代碼

評分

	13^# 無效樓層，該帖已經被刪除

	15^# 無效樓層，該帖已經被刪除