msp430 adc電壓值顯示在1602上

[復制鏈接]

電梯直達

樓主

ID:371533 發表于 2018-7-14 16:05 | 只看該作者回帖獎勵

|倒序瀏覽 |閱讀模式

#include <msp430x14x.h>
#include "Keypad.h"
#include "cry1602.h"
#include "x9c103.h"
#define uchar unsigned char
#define uint unsigned int
#define Num_of_Results 128
extern uchar num[];
uchar tishi[] = {"Vout:"};
static uint results[Num_of_Results]; //保存ADC轉換結果的數組 // is not used for anything.
void Trans_val(uint Hex_Val);
void keytest();
/************************主函數****************************/
void main(void)
{
WDTCTL = WDTPW+WDTHOLD; //關閉看門狗
LcdReset(); //復位1602液晶
DispNChar(0,0,5,tishi);
DispNChar(0,1,4,"set:"); //顯示提示信息
Init_Keypad(); //初始化鍵盤端口
P1DIR|=0X07;
x9c_init();
P6SEL |= 0x01; // 使能ADC通道
ADC12CTL0 = ADC12ON+SHT1_8+MSC; // 打開ADC，設置采樣時間
ADC12CTL1 = SHP+CONSEQ_2; // 使用采樣定時器
ADC12IE = 0x01; // 使能ADC中斷
ADC12CTL0 |= ENC; // 使能轉換
ADC12CTL0 |= ADC12SC; // 開始轉換
_EINT();
LPM0;
}
/*******************************************
函數名稱：ADC12ISR
功能：ADC中斷服務函數，在這里用多次平均的
計算P6.0口的模擬電壓數值
參數：無
返回值：無
********************************************/
#pragma vector=ADC12_VECTOR
__interrupt void ADC12ISR (void)
{
static uint index = 0;
results[index++] = ADC12MEM0; // Move results
if(index == Num_of_Results)
{
uchar i;
unsigned long sum = 0;
index = 0;
for(i = 0; i < Num_of_Results; i++)
{
sum += results[i];
}
sum >>= 7; //除以512
Trans_val(sum);
}
keytest();
}
/*******************************************
函數名稱：Trans_val
功能：將16進制ADC轉換數據變換成三位10進制
真實的模擬電壓數據，并在液晶上顯示
參數：Hex_Val--16進制數據
n--變換時的分母等于2的n次方
返回值：無
********************************************/
void Trans_val(uint Hex_Val)
{
unsigned long caltmp;
uint Curr_Volt;
uchar t1,i;
uchar ptr[4];
caltmp = Hex_Val;
caltmp = (caltmp << 5) + Hex_Val; //caltmp = Hex_Val * 33
caltmp = (caltmp << 3) + (caltmp << 1); //caltmp = caltmp * 10
caltmp = (caltmp << 1) + caltmp;
Curr_Volt = caltmp >> 11; //Curr_Volt = caltmp / 2^n
Curr_Volt+=60;
ptr[0] = (Curr_Volt-(Curr_Volt/1000)*1000) / 100; //Hex->Dec變換
t1 = Curr_Volt -(Curr_Volt/1000)*1000- (ptr[0] * 100);
ptr[2] = t1 / 10;
ptr[3] = t1 - (ptr[2] * 10);
ptr[1] = -2; //shuzi表中第10位對應符號"."
//在液晶上顯示變換后的結果
Disp1Char(5,0,'1');
for(i = 0;i < 4;i++)
Disp1Char((6 + i),0,ptr[i]+48);
}